3P overflow siphon UNO DN100 for plastic cisterns

Article No. 4000260

Overflow with odor trap and suction of surface water. With special threaded connection DN 100, ideal for thin-walled rainwater storage tanks.

• With integrated rodent barrier
• Dimensions: 540 x 190 x 270 mm
• Material: Polyethylene
• Union nut: DN 100 with O-ring

Article No. 4000265

Overflow with odor trap and suction of surface water.

• DN100, ideal for concrete rainwater storage tanks
• With integrated rodent barrier
• Dimensions: 660 x 190 x 270 mm
• Material: Polyethylene

3P backflow flap UNO

Article No. 4000930

Features like the 3P backflow flap DN 100 (p. 146), additionally with special overflow siphon UNO, overflow with odor trap and suction of surface water.

• Dimensions: 850 x 260 mm

3P backflow flap DUO

Article No. 4000940

Features such as the 3P backflow flap DN 100, plus special overflow with odor trap and suction of surface water.
The 3P backflow flap DUO is installed between the filter and the overflow connection in the rainwater tank. This eliminates unnecessary installation times and fittings. The fixed height offset in the overflow siphon prevents installation errors and thus ensures functionality.
Overflow siphon with a double-sided snorkeling of the surface water in the rainwater storage tank, no way through for rodents.

• Dimensions: 850 x 480 mm

Functional principle :
Dirt particles that are lighter than water (e.g. pollen) slowly rise and float on the water surface. This floating layer is when the cistern overflows, the water is removed by the specially shaped overflow siphon with skimmer effect. Connection nozzle DN 50 to use an HT pipe as a support pipe to use. Is supported on the rainwater storage tank wall. The overflow siphon is filled with water (odor trap). If the storage tank has a low water level the support helps to keep the overflow siphon in the correct position.

3P overflow siphon DUO DN100

Article No. 4000200

Overflow with odor trap and suction of surface water. The 3P overflow siphon DUO DN 100 is installed between the filter and the overflow connection in the rainwater tank. This eliminates unnecessary assembly times and fittings. The fixed height offset in the overflow siphon prevents installation errors and thus ensures functionality. Overflow siphon with a snorkeling of the surface water in the rainwater tank on both sides.

• Height offset: 125 mm
• No passage for rodents
• Connection piece for
• support tube available
• Connection: DN 100
• Material: Polyethylene
• Dimensions: 500 x 360 x 480 mm

Functional principle :
Dirt particles that are lighter than water (e.g. flower pollen) slowly rise and float on the surface of the water.
This floating layer is removed when the cistern overflows through the specially shaped overflow siphon with skimmer effect. Connection nozzle DN 50, to use an HT pipe as a support pipe. Is supported on the rainwater storage tank wall. The overflow siphon is filled with water (odor trap).
If the tank has a low water level, the support helps to keep the overflow siphon in the correct position.

3P overflow siphon MONO DN100

Article No. 4000250

Overflow with odor trap and suction of surface water. Overflow siphon with a snorkeling of the surface water in the rainwater tank on both sides. Regular overflow of the cistern is important for consistently good water quality in order to prevent the water from “rotting”. The floating layer could seal off the water surface in such a way that no oxygen can get into the water and therefore an anaerobic decomposition process could take place.

• No passage for rodents
• Connection: DN 100
• Dimensions: 500 x 360 x 480 mm

3P flat tank siphon DN100
(32 cm / 36 cm)

with rodent barrier plastic

Article No. 1300530 / 1300535

The siphon for flat tanks offers the possibility of achieving optimal water quality even with low tank heights. By cutting the outlet to the appropriate length, the siphon can safely drain the upper layer of water and prevent unpleasant odors. The siphon offers you the possibility of storing water up to 50% of the height of the drain pipe or draining it directly to the level of the base.

• Dimensions: 390 x 430 x Ø 110 mm
• Material: Polyethylene
• Plug-in component

3P overflow siphon DN100

without height offset

Article No. 4000218

Odor trap to the sewer without rodent barrier.

• Dimensions: 425 x 560 x 110 mm
• Material: Polyethylene
• Plug-in component

3P overflow siphon DN100

Article No. 4000310

Odor trap to the sewer with integrated rodent barrier made of stainless steel.

• Dimensions: 425 x 560 x 110 mm
• Material: Polyethylene
• Plug-in component

3P overflow siphon DN100

with rodent barrier plastic

Article No. 4000315

Odor trap to the sewer with integrated plastic rodent barrier.

• Dimensions: 425 x 560 x 110 mm
• Material: Polyethylene
• Plug-in component

3P overflow siphon DN100

Article No. 4000210

Odor trap to the sewer.

• Dimensions: 425 x 560 x 110 mm
• Material: Polyethylene
• Plug-in component

3P overflow siphon DN150

Standard without rodent barrier

Article No. 4000360

Overflow siphon with odor trap DN 150 which is installed in the drain to the sewerage system.

• Dimensions: 785 x 385 x 470mm
• Material: Polyethylene
• Ready-to-connect component
• Without rodent barrier

3P overflow siphon DN150

without height offset

Article No. 4000365

Overflow siphon with odor trap DN 150 which is installed between the filter and the sewerage system.

• Dimensions: 785 x 385 x 470mm
• Material: Polyethylene
• Ready-to-connect component
• Without rodent barrier

3P overflow siphon

with rodent barrier stainless steel

DN200 Article No. 4000285 / DN250 Article No. 4000295

The overflow features an odor trap and efficiently removes surface water. A stainless steel sheet cover ensures no entry for rodents. This is a standard overflow system.

The cistern plays a vital role in maintaining consistently high water quality, preventing the water from stagnating or “rotting.” A floating layer can seal the water surface, blocking oxygen entry and thereby avoiding anaerobic decomposition processes. This makes it particularly suitable for use in large systems.

The 3P Overflow Siphon (DN 200 / DN 250) can be connected to a DN 200 or DN 250 plastic pipe. It must be securely installed in the cistern, as it becomes significantly heavy when filled. At low water levels, the buoyancy force is reduced. Therefore, the siphon is secured to the cistern using multiple eyelets. Additionally, it can be supported against the wall of the rainwater storage tank with a 50 mm HT pipe.

• Connection: DN 200 / DN 250
• Material: Polyethylene
• Rodent barrier: stainless steel
• Dimensions: 375 x 659 x 765 mm

Functional principle :
Dirt particles that are lighter than water (e.g. flower pollen) slowly rise and float on the surface of the water.

This floating layer is removed when the cistern overflows through the specially shaped overflow siphon with skimmer effect.
The floating layer could seal off the water surface in such a way that anaerobic degradation would take place.

Inlet with rodent barrier eyelets for hanging
connection nozzle DN 50, a HT pipe as a support pipe to use drain DN 200 / DN 250

Article No. 4000600

The floating suction fitting is the fourth purification stage in rainwater use. The rainwater should not be taken directly from the lowest point in the cistern, otherwise sediment particles will be stirred up and transported. Therefore, the water should be taken from higher regions in the cistern is recommended.

Consisting of :

• Floating ball: Ø 140 mm
• Filter basket mesh size: 1.2 mm
• Check valve: 1″ with hose nozzle and disc

3P pump base with floating suction fitting

Article No. 4000680

Consisting of :

• Pump base (PE) for submersible pressure pumps Ø 130 mm
  (not included)
• Floating ball: Ø 140 mm
• filter basket
• suction hose 1″: 1 m
• double socket

3P Floating Intake Fitting 1″

with 1.5m hose Article No. 4000615

with 2.0m hose Article No. 4000620

with 2.5m hose Article No. 4000622

with 3.0m hose Article No. 4000632

3P Floating suction fitting with suction hose for extracting rainwater from the rainwater storage tank, for connecting PE pipes, Ø 32 mm.

Consisting of :

• Floating ball: Ø 140 mm
• Filter basket mesh size: 1.2 mm
• Check valve: 1″ with hose nozzle and disc
• connection angle for 1″ PE pipes
• Suction hose: 1.5 – 3 m

3P suction fitting for submersible pumps

Article No. 4000908

3P Floating suction fitting for submersible pumps for extracting rainwater from the rainwater storage tank.

Consisting of :

• Floating ball: Ø 140 mm
• filter basket
• 1.5 m suction hose Vacu-Press
• spacers
• Connection: Brass nozzle 1“ AG

3P Calmed Inlet DN100

Article No. 4000180

The 3P Calmed Inlet ensures a calm flow of rainwater into the storage tank. The calmed inlet of the water prevents turbulence the sediment layer is avoided, while at the same time oxygen is supplied to the lower part of the storage water. The water remains fresh.

• Dimensions: L: 400 x W: 175 x H: 110 mm
• Material: Polyethylene
• Connection option: for pipes DN100

3P Calmed Inlet DN125

Article No. 4000100

Ensures a calm inflow of rainwater within the storage tank. Fine dirt particles remaining in the water slowly sink to the bottom.
A sediment layer forms, which has been proven to have a positive effect on the stored rainwater. Rainwater storage tank with sediment layer
have clearer water. The calm inflow of water prevents the stirring up of this sediment layer, while at the same time the lower part Oxygen is added to the stored water. The oxygen prevents anaerobic decomposition in the cistern. The water stays fresh.
The 3P calmed inlet is the second purification stage in the rainwater storage tank.

• Dimensions: L: 320 x W: 155 x H: 100 mm
• Material: Polyethylene
• Connection option: for pipes DN125

3P Calmed Inlet DN150 round

Article No. 4000190

The 3P Calmed Inlet ensures a calm flow of rainwater into the storage tank. The calmed inlet of the water.
The sediment layer is prevented from being stirred up, and at the same time oxygen is supplied to the lower part of the storage water. The water stays fresh.
At the same time, the 3P Calmed Inlet DN 150 stabilizes the installation of the entire filter system thanks to its round shape.

• Dimensions: Ø 340 mm x H: 105 mm
• Material: Polyethylene
• Ready-to-connect component

3P Calmed Inflow
DN200/DN250/DN300

DN200 Article No. 4000155

DN250 Article No. 4000160

DN300 Article No. 4000165

Ensures a calm inflow of rainwater within the rainwater storage tank. Fine dirt particles remaining in the water slowly sink to the bottom.
A sediment layer is formed, which has been proven to have a positive influence on the stored rainwater, because rainwater storage tanks with a sediment layer have clearer water. The calm inflow of water prevents the stirring up of this sediment layer, while at the same time the lower part Oxygen is added to the storage water. Ideal for use in large systems. The 3P calmed inlet can be connected to a plastic pipe DN 150 / 200 / 250 / 300 be connected.

• Dimensions: 725 x 527 x 360 mm

3P suction hose Vacu-Press

Article No. 4000642

The 3P Vacu-Press suction hose consists of two layers and has an internal stainless steel spiral that prevents the hose from kinking.

• rubber suction hose: Ø 36 mm
• Sold by the meter, suitable for 1″ nozzles

3P filter pillows for deep filtration

set of 2 Article No. 4000710

set of 3 Article No. 4000720

set of 5 article no. 4000730

Specially developed polymer fiber for cleaning rainwater. Through the combination of various polymer fibers and deliberately chosen spherical shape an enormously large filter surface can be guaranteed. The resulting 3D filtration enables not only superficial cleaning but also deep filtration.
Due to the excellent dirt absorption capacity, even the finest dirt particles in the micrometer range can be accurately removed from the
Rainwater can be removed. Due to the large surface area, half-yearly or annual maintenance or replacement of the 3P filter pillows is completely sufficient.

• Highest water quality
• Easy filter change
• Easy handling
• For almost all filter types
• universally applicable
• Low weight
• High selectivity of 8 micrometers
• Fibers certified according to ÖKO-TEX® Standard 100
• Can be retrofitted or expanded at any time
• Easy disposal
• Durable
• Easy maintenance
• Recycled product