ACCESSORIES
3P Automatic water make-up system
Art.-No. 5000700
The automatic water make-up system is a control system that has been specially developed for monitoring and controlling rainwater tanks and connected domestic waterworks control. The system consists of a control unit, a probe and a solenoid valve.
The control unit is microprocessor-controlled and enables continuous drinking water replenishment in rainwater tanks. The system has dry-running protection and a safety cut-out to prevent damage to the system.
There are two selectable programme times, for normal or increased water consumption. This means that the system can automatically switch between different programme times to optimise the consumption of drinking water while maintaining the rainwater supply in the tank. The automatic replenishment system is easy to use and can be installed quickly.
The 3P automatic water make-up system a very practical solution for monitoring and controlling rainwater tanks and connected domestic waterworks, which enables continuous drinking water make-up and optimises water consumption at the same time.
3P Backwater flap DN100
Art.-No. 4000910
The 3P backwater flap DN 100 prevents wastewater from entering the rainwater storage tank in the event of backwater. It is suitable for installation in DN 100 pipes and consists of a commercially available backwater protection from the wastewater sector. The backwater flap allows the water flow to flow in one direction only. If the water flows in the opposite direction, the flap closes and prevents dirt from entering the rainwater storage tank. The flap is fitted with a special seal.
• Dimensions: W: 500 mm x H: 260 mm
3P Wall bushing DN100
2x Ø 32 mm, 1x Ø 16 mm Art.-No. 5000300
1x Ø 36 mm, 1x Ø 16 mm Art.-No. 5000310
1x Ø 32 mm, 1x Ø 16 mm Art.-No. 5000320
Wall bushings seal cables at bushing points. Depending on the application, different wall ducts are required.
Usually Ø 32 mm for 1“ PE pipe, Ø 36 mm for 1“ suction hose, cable for power supply of submersible pumps and for water level measurement Ø 16 mm for the PE pipe of the backwash device.
This opening is always included in our wall ducts, but can be closed with the enclosed plug if not required. A wall duct consists of a 30 mm thick rubber plate with 2 stainless steel plates and screw connections.
3P Pneumatic remote indicator
Art.-No. 5000500
Universal, pneumatic level measuring device for remote measurement up to 20 m, with capsule spring measuring mechanism
• Water level height continuously adjustable from 1 m to 2.5 m
• Measuring accuracy ± 3 % of full scale value
• Zero point correction and overpressure protection
• Adjustable pointer for easy consumption control
• Housing made of impact-resistant plastic for wall mounting
• Display in % filling level 147
3P Pipe clamp set
DN 100 Art.-No. 4000331
DN 150 Art.-No. 4000334
For fastening the retention throttles consisting of:
• 2 pcs. V2A threaded rods
• 2 pcs. M8 brass dowel
• 2 pcs. Pipe clamps DN 100 / DN 150
3P Labelling set
Art.-No. 4000700
Labelling set for rainwater utilisation systems according to DIN 1989. Each rainwater utilisation system should be labelled accordingly with information signs.
According to DIN 1989 rainwater utilisation systems consisting of:
- Sign: „Attention! A rainwater system is installed in this building.“
Exclude cross connections.“ Plastic, 2 mm thick, 200 x 150 mm, blue background, white lettering - Notice sign: „No drinking water“ Plastic, 1 mm thick, 120 x 60 mm,
white background, red lettering - Route warning tape: „No drinking water“ 0.14 mm thick, 10 m x 40 mm, yellow background, black lettering
- Pipe marking tape: „No drinking water“ Width: 76 mm,
green background, white lettering - Prohibition and instruction sign, diameter: 100 mm, white background, red symbol
3P Lip seal NW 100
Art.-No. 7000598
Rubber lip seal DN 100 for producing tight pipe penetrations in plastic cisterns with wall thicknesses of 8 to 12 mm.
- For plastic cistern
3P hole saw set Ø 64 – 127 mm
Art.-No. 9000274
The 3P hole saw set for professional drilling of holes in plastic cisterns.
- With diameters of 64 mm, 76 mm, 89 mm, 102 mm and 127 mm
- For plastic cisterns
Do you need specialist support or have questions for us?
Ms. Sonja Graf, your competent contact for projects, design, planning support and advice for the applications of the relevant data sheets.
Tel +49 (0) 7334 92460-11
Mail graf@3ptechnik.de
